computer broke.

2010-11-02 10:17:38

#276

Uzique: dasein.; +2,865|6680

GC_PaNzerFIN wrote:
HA! That guy did it wrong. You don't apply thermal paste on CPU with such cooler base. You put the thermal paste on the heatpipes, not the CPU.

mine has heatpipes and i put a line down the middle in the direction of the pipes... same as i did with my q6600 years ago

managed to get the heatsink bolted on, finally. pain in the ass. the 'X' directions tip and 1-align, 2-screw, 3- tighten technique worked... ish

now the other bitching task is mounting the mobo inside my case. it doesn't seem to want to fit snugly enough.

0.5mm to the 'right' of the true-side and I/O mounting plate... i have to kinda apply sideways force to get the mobo pins to line-up

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 12:00:51

#277

presidentsheep: Back to the Fuhrer; +208|6170|Places 'n such

Uzique wrote:
GC_PaNzerFIN wrote:
HA! That guy did it wrong. You don't apply thermal paste on CPU with such cooler base. You put the thermal paste on the heatpipes, not the CPU.
mine has heatpipes and i put a line down the middle in the direction of the pipes... same as i did with my q6600 years ago

managed to get the heatsink bolted on, finally. pain in the ass. the 'X' directions tip and 1-align, 2-screw, 3- tighten technique worked... ish

now the other bitching task is mounting the mobo inside my case. it doesn't seem to want to fit snugly enough.

0.5mm to the 'right' of the true-side and I/O mounting plate... i have to kinda apply sideways force to get the mobo pins to line-up

Mines like that, think its the shitty case. Dont spose it was from maplin?

I'd type my pc specs out all fancy again but teh mods would remove it. Again.

2010-11-02 12:22:03

#278

Uzique: dasein.; +2,865|6680

ok, set it all up

completely wired... all wired properly, too

ABSOLUTELY NO POWER ON

the PSU fan span for about 0.5 seconds... and then nothing

what could be causing this? 2 completely different computers... i am utterly at a loss

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 12:25:05

#279

Uzique: dasein.; +2,865|6680

ok this time it started up, the front fan went... the hard-drives span up...

no rear fan, no CPU fan, nothing... and they're all plugged in

wtf causes only half the thing to boot?

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 12:26:13

#280

presidentsheep: Back to the Fuhrer; +208|6170|Places 'n such

Getting any POST beeps?

I'd type my pc specs out all fancy again but teh mods would remove it. Again.

2010-11-02 12:37:57

#281

Uzique: dasein.; +2,865|6680

i left the speaker out at the moment

everything is booting now except for the heatsink/CPU fan

the CPU-FAN jumper cable is definitely connected, but the fan doesn't power on... at all.

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 12:59:39

#282

Ilocano: buuuurrrrrrppppp.......; +341|6876

Is it a two or three pin connection? Tried it on another socket?

2010-11-02 13:02:28

#283

Uzique: dasein.; +2,865|6680

the heatsink is a 4-pin connection and i've tried it on both 4-pin sockets... no fan spinning

i have also connected the machine to a monitor and keyboard but it seems it is sending no display signal

the fan on the ATI card spins on power-up, so it's getting juice

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 13:05:39

#284

Ilocano: buuuurrrrrrppppp.......; +341|6876

Both PSU plugs connected to MB? Unplug the new GPU. Put in your old one for now. Use DVI, not HDMI.

2010-11-02 13:08:40

#285

Uzique: dasein.; +2,865|6680

i've taken out the RAM and the GPU

installed the mobo speaker

with no RAM in it just lets out a long, quick-beeping noise that doesn't stop

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 13:13:06

#286

Ilocano: buuuurrrrrrppppp.......; +341|6876

Where you using DVI or HDMI?

2010-11-02 13:15:22

#287

Uzique: dasein.; +2,865|6680

it doesn't matter... if i power on the machine with no graphics, no RAM, no anything...

i get a short, long, machine-gun like beeping noise

mobo dead? just great

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 13:25:47

#288

Ilocano: buuuurrrrrrppppp.......; +341|6876

Chill pill

- plug in GPU. Make sure both power connections are connected. Plug to DVI
- seat in just one Ram
- USB or PS2 keyboard? If you got a PS2, plug it in. BIOS might be lookiing for a PS2 keyboard.
- reset CMOS

2010-11-02 13:28:26

#289

Uzique: dasein.; +2,865|6680

i've got a hdmi cable from a housemate. it sends out no display signal.

with 1 RAM and 0 RAM, it doesn't work... just machine-gun beeping.

only a USB keyboard here i'm afraid, but doesn't matter as i can't see any POST screens, anyway

crucially the CPU FAN is still not spinning so i'm afraid of leaving it running for 30secs+ at once

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 13:32:14

#290

Ilocano: buuuurrrrrrppppp.......; +341|6876

HDMI is flaky when building a new rig. It often doesn't go on unitl OS is ready. You will need DVI first until everything is all good.

Got a spare fan to replace the HS fan for now?

2010-11-02 13:34:07

#291

Uzique: dasein.; +2,865|6680

no, just case fans... and another heatsink... but fuck remounting ANOTHER heatsink tonight after that nightmare

i just don't understand it...

the hard-drives seem to continually start and restart loading, too. it's like the power is fucked or something.

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 13:41:25

#292

GC_PaNzerFIN: Work and study @ Technical Uni; +528|6624|Finland

I am confused what the situation is now.

It is very simple, plug in only required components, no HDD or anything like that, make sure the rams are in right slots (primary ones) and graphics card is in the primary 16X slot, pci-e power cables connected the gfx card, 8pin and 24pins to the mobo etc.

You may even put it together on table.

Last edited by GC_PaNzerFIN (2010-11-02 13:42:49)

3930K | H100i | RIVF | 16GB DDR3 | GTX 480 | AX750 | 800D | 512GB SSD | 3TB HDD | Xonar DX | W8

2010-11-02 13:43:12

#293

Ilocano: buuuurrrrrrppppp.......; +341|6876

No need to remove the heatsink. Use a similar size fan to replace the HS fan.

Next, get a DVI connection going.

Is the harddrive clean, or are you using one with an OS already?

Which PSU are you using?

Edit: yeah, HD not needed at this point.

2010-11-02 13:48:23

#294

Uzique: dasein.; +2,865|6680

the situation is that the heatsink fan doesn't seem to work, period

i'm using a corsair 600w PSU which is enough to power this small build atm

i'm stripping it all down again...

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 13:56:05

#295

Ilocano: buuuurrrrrrppppp.......; +341|6876

Does the PSU have a 4-pin Fan connection? Try that. If not, replace just the fan.

2010-11-02 14:00:30

#296

Uzique: dasein.; +2,865|6680

nah the PSU doesn't

the PSU didn't have a connection for my creative x-fi card, either... but that's the least of my worries right now

i'm reseating the mobo at the moment to rule out the possibility of it shorting out against the case

starting at the bottom

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

2010-11-02 14:03:09

#297

Ilocano: buuuurrrrrrppppp.......; +341|6876

Like Panzer noted, keep it out of the case for now.

Lay the unit on some non-conductive, non-static surface (MB box?), plug Ram, GPU with DVI, CPU/HS/Fan only. Reset CMOS. Step by step.

2010-11-02 14:05:16

#298

-CARNIFEX-[LOC]: Da Blooze; +111|6863

Uzique wrote:
i'm reseating the mobo at the moment to rule out the possibility of it shorting out against the case

starting at the bottom

I haven't replied to this thread b/c there are much more capable minds helping you, but this is exactly what gave my last PC issues that were very similar to what you're describing. So good luck, and hopefully it's something simple like reseating the mobo.

(and I determined this by having everything work laid out on a wooden table, as is being suggested)

Last edited by -CARNIFEX-[LOC] (2010-11-02 14:06:33)

https://static.bf2s.com/files/user/12516/Bitch%20Hunter%20Sig.jpg

2010-11-02 14:14:56

#299

Ilocano: buuuurrrrrrppppp.......; +341|6876

All these properly placed?

https://static.bf2s.com/files/user/11550/standoffs.jpg

2010-11-02 14:24:53

#300

Uzique: dasein.; +2,865|6680

yeah they're placed in the right spots for my socket-type... i screwed them in with big-head screws, removed them all and tried again with small-head screws... still same beeping problem, and no CPU fan.

sorting out all the wiring now so that i can run the mobo off a cardboard box with an anti-static sheet on it

_{libertarian benefit collector - anti-academic super-intellectual}. _{http://mixlr.com/the-little-phrase/}

BF2S Forums computer broke.

GC_PaNzerFIN wrote:

Uzique wrote:

GC_PaNzerFIN wrote:

Uzique wrote:

Board footer